Logo

BMW Fault Code - 53

Check 53 Fault Code

BMW Fault Code: 53

53 - Valve coils

System: Electronic Damper Control

BMW System: EDC

Type: Chassis

BMW Fault Code: 53

53 - Valve coils

System: Electronic Damper Control

BMW System: EDC

Type: Chassis

Wide Open Throttle (WOT) Switch

Fault Code Table : DME M1.1

The BMW DME M1.1 (and similar, 1.2 and 1.3) is an early Bosch Motronic ECU, used on all of the 6 Cylinder BMWs up until 1990, and a few more after that.

M1.1 and M1.3 was used on the M20, M30 and M40 engines, whilst M1.2 was used on the S38 and M70, which are the early E34 M5 engines and the early V12s.

Wide Open Throttle (WOT) Switch

Fault Code Table : DME M1.2

The BMW DME M1.1 (and similar, 1.2 and 1.3) is an early Bosch Motronic ECU, used on all of the 6 Cylinder BMWs up until 1990, and a few more after that.

M1.1 and M1.3 was used on the M20, M30 and M40 engines, whilst M1.2 was used on the S38 and M70, which are the early E34 M5 engines and the early V12s.

Wide Open Throttle (WOT) Switch

Fault Code Table : DME M1.3

The BMW DME M1.1 (and similar, 1.2 and 1.3) is an early Bosch Motronic ECU, used on all of the 6 Cylinder BMWs up until 1990, and a few more after that.

M1.1 and M1.3 was used on the M20, M30 and M40 engines, whilst M1.2 was used on the S38 and M70, which are the early E34 M5 engines and the early V12s.

Lambda Sensor Heater

Fault Code Table : MS40

MS40 was a new ECU for BMW, manufactured by Siemens instead of the previous Bosch Motronics. BMW split the M50 24v engines and used Siemens for some of the 2.0 litres, and Bosch continued on with the 2.5l.

MS40.0 is a rare ECU used on non VANOS 2.0l, and MS40.1 introduced VANOS control.

Idle Speed Actuator

Fault Code Table : MS41

The next generation Siemens MS ECUs introduced many of the OBD2 features. This includes Catalytic Converter monitoring and Long / Short term Fueling and Ignition Adaptation. The MS41 was used on the M52 series of engines, MS42 on the M52TU series, and MS43 on the M43 4 Cylinders.

The OBD2 P codes fault protocol was not activated in European markets on this group, as currently it was not required by law.

Idle Speed Actuator

Fault Code Table : MS42

The next generation Siemens MS ECUs introduced many of the OBD2 features. This includes Catalytic Converter monitoring and Long / Short term Fueling and Ignition Adaptation. The MS41 was used on the M52 series of engines, MS42 on the M52TU series, and MS43 on the M43 4 Cylinders.

The OBD2 P codes fault protocol was not activated in European markets on this group, as currently it was not required by law.

Idle Speed Actuator

Fault Code Table : MS43

The next generation Siemens MS ECUs introduced many of the OBD2 features. This includes Catalytic Converter monitoring and Long / Short term Fueling and Ignition Adaptation. The MS41 was used on the M52 series of engines, MS42 on the M52TU series, and MS43 on the M43 4 Cylinders.

The OBD2 P codes fault protocol was not activated in European markets on this group, as currently it was not required by law.

Electric Fan Relay

Fault Code Table : DME MSS50

The MSS50 is a special ECU designed solely for the European E36 M3 3.2. Designed by Siemens, it integrates full Vanos control for both Intake and Exhaust Cams inside a single ECU, unlike the previous M3.3 which required a separate VNC Vanos Controller

Electric Fan

Fault Code Table : DME MSS52

The MSS52 is an M Power ECU designed to run the E39 M5, the Z8 Roadster, and also the Wiesmann Roadsters. The MSS54 is used on the E46 M3 and on some Z3Ms. The system uses an Electronic Throttle to accurately control Air intake instead of the more common Cable throttles used on earlier vehicles

Electric Fan

Fault Code Table : DME MSS54

The MSS52 is an M Power ECU designed to run the E39 M5, the Z8 Roadster, and also the Wiesmann Roadsters. The MSS54 is used on the E46 M3 and on some Z3Ms. The system uses an Electronic Throttle to accurately control Air intake instead of the more common Cable throttles used on earlier vehicles

Misfire Cyl 4

Fault Code Table : DME M5.2.1

DME M5.2 and M5.2.1 are Bosch ECUs, used on the M44 4cyl engine, and the M62 V8, and the M72 V12.

Misfire Cyl 4

Fault Code Table : DME M5.2

DME M5.2 and M5.2.1 are Bosch ECUs, used on the M44 4cyl engine, and the M62 V8, and the M72 V12.

Misfire Detection Cyl 8

Fault Code Table : DME 7.2

The Bosch DME 7.2, also known as ME7.2, can be found on a number of V8 Petrol engines, used in the 5 and 7 Series amongst others. It uses Torque modeling to control the engine torque output depending on Throttle Pedal Position.

Coolant Temperature Sensor

Fault Code Table : DDE 2

DDE stands for Digital Diesel Electronics, and these were used on BMW’s Diesel engines. DDE2 is used on M41 and M51 engines. DDE 2.1 uses an updated Air Mass Meter with an Internal Air Temperature Sensor, whilst DDE2 has a separate sensor in the manifold.

Coolant Temperature Sensor

Fault Code Table : DDE 2.1

DDE stands for Digital Diesel Electronics, and these were used on BMW’s Diesel engines. DDE2 is used on M41 and M51 engines. DDE 2.1 uses an updated Air Mass Meter with an Internal Air Temperature Sensor, whilst DDE2 has a separate sensor in the manifold.

Coolant Temperature Sensor

Fault Code Table : DDE 2.2

This is an Updated version of the previous DDE 2.1, and was introduced in 1995. This system was used on the M51TU engines.

Wheel Sensor – Rear Left or Inlet Valve – Front Right

Fault Code Table : ABS 1

The first BMW ABS system, This was a 3 channel system, controlling braking to the front wheels,and a single line for both rear wheels. The wheel speed info could be passed via data lines to traction control systems, which could determine if the vehicle speed signal given from the rear driven axle did not match with the front wheel speed signals and request torque reduction intervention from the ASC (Anti Skid Control) throttle body.

About | Contact | Privacy

Copyright © 2019 All rights reserved. BMW Faults are listed in here BMWFaultCodes.com .