System: AirBag Multiple Restraint System
BMW System: AB
Type: Body
Inlet Air Temperature Sensor
The BMW DME M1.1 (and similar, 1.2 and 1.3) is an early Bosch Motronic ECU, used on all of the 6 Cylinder BMWs up until 1990, and a few more after that.
M1.1 and M1.3 was used on the M20, M30 and M40 engines, whilst M1.2 was used on the S38 and M70, which are the early E34 M5 engines and the early V12s.
Inlet Air Temperature Sensor
The BMW DME M1.1 (and similar, 1.2 and 1.3) is an early Bosch Motronic ECU, used on all of the 6 Cylinder BMWs up until 1990, and a few more after that.
M1.1 and M1.3 was used on the M20, M30 and M40 engines, whilst M1.2 was used on the S38 and M70, which are the early E34 M5 engines and the early V12s.
Inlet Air Temperature Sensor
The BMW DME M1.1 (and similar, 1.2 and 1.3) is an early Bosch Motronic ECU, used on all of the 6 Cylinder BMWs up until 1990, and a few more after that.
M1.1 and M1.3 was used on the M20, M30 and M40 engines, whilst M1.2 was used on the S38 and M70, which are the early E34 M5 engines and the early V12s.
Oil Level Sensor
The MSS50 is a special ECU designed solely for the European E36 M3 3.2. Designed by Siemens, it integrates full Vanos control for both Intake and Exhaust Cams inside a single ECU, unlike the previous M3.3 which required a separate VNC Vanos Controller
Oil Level Sensor Signal
The MSS52 is an M Power ECU designed to run the E39 M5, the Z8 Roadster, and also the Wiesmann Roadsters. The MSS54 is used on the E46 M3 and on some Z3Ms. The system uses an Electronic Throttle to accurately control Air intake instead of the more common Cable throttles used on earlier vehicles
Oil Level Sensor Signal
The MSS52 is an M Power ECU designed to run the E39 M5, the Z8 Roadster, and also the Wiesmann Roadsters. The MSS54 is used on the E46 M3 and on some Z3Ms. The system uses an Electronic Throttle to accurately control Air intake instead of the more common Cable throttles used on earlier vehicles
EKAT -Power Cat 1
DME M5.2 and M5.2.1 are Bosch ECUs, used on the M44 4cyl engine, and the M62 V8, and the M72 V12.
EKAT -Power Cat 1
DME M5.2 and M5.2.1 are Bosch ECUs, used on the M44 4cyl engine, and the M62 V8, and the M72 V12.
Camshaft sensor
The Bosch BMS46 is a Hybrid ECU, created from a joint effort with Siemens, and is used in later M43 engines used in the Z3 and E46 series.
Camshaft sensor
The Bosch BMS46 is a Hybrid ECU, created from a joint effort with Siemens, and is used in later M43 engines used in the Z3 and E46 series.
AirCon Switch
This is an Updated version of the previous DDE 2.1, and was introduced in 1995. This system was used on the M51TU engines.
Solenoid Valve
DDE 3 is the BMW name for the ECUs used on the M47 range on Diesel engines, also known as he Bosch EDC15. These are 4 Cylinder diesels, used in the E46 320d, and uses Common Rail Injection. Common Rail systems use a high pressure fuel rail with diesel injectors, as opposed to the mechanical injection systems, or the PD (Pumpe Düse) system where each injector also acts as a high pressure pump.
Copyright © 2019 All rights reserved. BMW Faults are listed in here BMWFaultCodes.com .
If you have own an another brand car/vehicle to check fault codes like : Audi Fault Code | Volvo Fault Codes