System: Integrated Heating/Air Conditioning
BMW System: IHKR
Type: Body
System: Integrated Heating/Air Conditioning
BMW System: IHKR
Type: Body
AirCon Compressor
The BMW DME M1.1 (and similar, 1.2 and 1.3) is an early Bosch Motronic ECU, used on all of the 6 Cylinder BMWs up until 1990, and a few more after that.
M1.1 and M1.3 was used on the M20, M30 and M40 engines, whilst M1.2 was used on the S38 and M70, which are the early E34 M5 engines and the early V12s.
AirCon Compressor
The BMW DME M1.1 (and similar, 1.2 and 1.3) is an early Bosch Motronic ECU, used on all of the 6 Cylinder BMWs up until 1990, and a few more after that.
M1.1 and M1.3 was used on the M20, M30 and M40 engines, whilst M1.2 was used on the S38 and M70, which are the early E34 M5 engines and the early V12s.
AirCon Compressor
The BMW DME M1.1 (and similar, 1.2 and 1.3) is an early Bosch Motronic ECU, used on all of the 6 Cylinder BMWs up until 1990, and a few more after that.
M1.1 and M1.3 was used on the M20, M30 and M40 engines, whilst M1.2 was used on the S38 and M70, which are the early E34 M5 engines and the early V12s.
Brake Light Switch or Pedal Value Signal
The next generation Siemens MS ECUs introduced many of the OBD2 features. This includes Catalytic Converter monitoring and Long / Short term Fueling and Ignition Adaptation. The MS41 was used on the M52 series of engines, MS42 on the M52TU series, and MS43 on the M43 4 Cylinders.
The OBD2 P codes fault protocol was not activated in European markets on this group, as currently it was not required by law.
Brake Light Switch or Pedal Value Signal
The next generation Siemens MS ECUs introduced many of the OBD2 features. This includes Catalytic Converter monitoring and Long / Short term Fueling and Ignition Adaptation. The MS41 was used on the M52 series of engines, MS42 on the M52TU series, and MS43 on the M43 4 Cylinders.
The OBD2 P codes fault protocol was not activated in European markets on this group, as currently it was not required by law.
Brake Light Switch or Pedal Value Signal
The next generation Siemens MS ECUs introduced many of the OBD2 features. This includes Catalytic Converter monitoring and Long / Short term Fueling and Ignition Adaptation. The MS41 was used on the M52 series of engines, MS42 on the M52TU series, and MS43 on the M43 4 Cylinders.
The OBD2 P codes fault protocol was not activated in European markets on this group, as currently it was not required by law.
Lambda Sensor Heater Post Cat Bank 2
The MSS52 is an M Power ECU designed to run the E39 M5, the Z8 Roadster, and also the Wiesmann Roadsters. The MSS54 is used on the E46 M3 and on some Z3Ms. The system uses an Electronic Throttle to accurately control Air intake instead of the more common Cable throttles used on earlier vehicles
Lambda Sensor Heater Post Cat Bank 2
The MSS52 is an M Power ECU designed to run the E39 M5, the Z8 Roadster, and also the Wiesmann Roadsters. The MSS54 is used on the E46 M3 and on some Z3Ms. The system uses an Electronic Throttle to accurately control Air intake instead of the more common Cable throttles used on earlier vehicles
Cat Efficiency Bank 1
DME M5.2 and M5.2.1 are Bosch ECUs, used on the M44 4cyl engine, and the M62 V8, and the M72 V12.
Cat Efficiency Bank 1
DME M5.2 and M5.2.1 are Bosch ECUs, used on the M44 4cyl engine, and the M62 V8, and the M72 V12.
Catalytic Converter Efficiency Bank 1
The Bosch DME 7.2, also known as ME7.2, can be found on a number of V8 Petrol engines, used in the 5 and 7 Series amongst others. It uses Torque modeling to control the engine torque output depending on Throttle Pedal Position.
DDE Error
DDE 3 is the BMW name for the ECUs used on the M47 range on Diesel engines, also known as he Bosch EDC15. These are 4 Cylinder diesels, used in the E46 320d, and uses Common Rail Injection. Common Rail systems use a high pressure fuel rail with diesel injectors, as opposed to the mechanical injection systems, or the PD (Pumpe Düse) system where each injector also acts as a high pressure pump.
Gas Valve – Potentiometer Error
The first BMW ABS system, This was a 3 channel system, controlling braking to the front wheels,and a single line for both rear wheels. The wheel speed info could be passed via data lines to traction control systems, which could determine if the vehicle speed signal given from the rear driven axle did not match with the front wheel speed signals and request torque reduction intervention from the ASC (Anti Skid Control) throttle body.
Rear Output Valve
The updated version of BMW’s ABS system, this was more advanced. Improvements include a 4 channel system for independent rear wheel braking, which allowed a more active ASC system. With individual braking, not only could a torque reduction be requested via the ASC secondary throttle body, but independent wheel braking could be used to control individual wheel slip as part of a stability program.
Copyright © 2019 All rights reserved. BMW Faults are listed in here BMWFaultCodes.com .
If you have own an another brand car/vehicle to check fault codes like : Audi Fault Code | Volvo Fault Codes