Logo

BMW Fault Code - 202

Check 202 Fault Code

BMW Fault Code: 202

202 - Oxygen sensor control limit, cylinders 1-3; Z3 and 323i US only: this fault affects cylinder 1-6

System: Digital Motor Electronics

BMW System: DME

Type: Drive

BMW Fault Code: 202

202 - Misfiring, cylinder 7 with cylinder cutout

System: Digital Motor Electronics

BMW System: DME

Type: Drive

Control unit

Fault Code Table : DME M1.7

The Motronic 1.7 and subfamilies, and the M3 and it’s variants are the next generation of BMW ECUs. The M1.7 was used on the M40, M42 and M70, the M1.7.1 was used solely for the S70, used in the BMW 850CSi. M1.7.2 was used for the M42 and M43 4 Cylinders. The M3.1 is a 6cyl ECU, used on the early M50 24v engines without VANOS. The M3.3 family were used to run the later 3.8 litre S38b38, the S50 3.0 M3, and the M60 V8s. M3.3.1 included VANOS control, and is used on M50 engines with VANOS, introduced to the E34 and E36 in 1992.

Control unit

Fault Code Table : DME M1.7.1

The Motronic 1.7.1 and subfamilies, and the M3 and it’s variants are the next generation of BMW ECUs. The M1.7 was used on the M40, M42 and M70, the M1.7.1 was used solely for the S70, used in the BMW 850CSi. M1.7.2 was used for the M42 and M43 4 Cylinders. The M3.1 is a 6cyl ECU, used on the early M50 24v engines without VANOS. The M3.3 family were used to run the later 3.8 litre S38b38, the S50 3.0 M3, and the M60 V8s. M3.3.1 included VANOS control, and is used on M50 engines with VANOS, introduced to the E34 and E36 in 1992.

Control unit

Fault Code Table : DME M1.7.2

The Motronic 1.7.2 and subfamilies, and the M3 and it’s variants are the next generation of BMW ECUs. The M1.7 was used on the M40, M42 and M70, the M1.7.1 was used solely for the S70, used in the BMW 850CSi. M1.7.2 was used for the M42 and M43 4 Cylinders. The M3.1 is a 6cyl ECU, used on the early M50 24v engines without VANOS. The M3.3 family were used to run the later 3.8 litre S38b38, the S50 3.0 M3, and the M60 V8s. M3.3.1 included VANOS control, and is used on M50 engines with VANOS, introduced to the E34 and E36 in 1992.

Control unit

Fault Code Table : DME M3.1

The Motronic 1.7 and subfamilies, and the M3 and it’s variants are the next generation of BMW ECUs. The M1.7 was used on the M40, M42 and M70, the M1.7.1 was used solely for the S70, used in the BMW 850CSi. M1.7.2 was used for the M42 and M43 4 Cylinders. The M3.1 is a 6cyl ECU, used on the early M50 24v engines without VANOS. The M3.3 family were used to run the later 3.8 litre S38b38, the S50 3.0 M3, and the M60 V8s. M3.3.1 included VANOS control, and is used on M50 engines with VANOS, introduced to the E34 and E36 in 1992.

Control unit

Fault Code Table : DME M3.3

The Motronic 1.7 and subfamilies, and the M3 and it’s variants are the next generation of BMW ECUs. The M1.7 was used on the M40, M42 and M70, the M1.7.1 was used solely for the S70, used in the BMW 850CSi. M1.7.2 was used for the M42 and M43 4 Cylinders. The M3.1 is a 6cyl ECU, used on the early M50 24v engines without VANOS. The M3.3 family were used to run the later 3.8 litre S38b38, the S50 3.0 M3, and the M60 V8s. M3.3.1 included VANOS control, and is used on M50 engines with VANOS, introduced to the E34 and E36 in 1992.

Lambda Regulation Bank 1 Post Cat

Fault Code Table : MS41

The next generation Siemens MS ECUs introduced many of the OBD2 features. This includes Catalytic Converter monitoring and Long / Short term Fueling and Ignition Adaptation. The MS41 was used on the M52 series of engines, MS42 on the M52TU series, and MS43 on the M43 4 Cylinders.

The OBD2 P codes fault protocol was not activated in European markets on this group, as currently it was not required by law.

Lambda Regulation Bank 1 Post Cat

Fault Code Table : MS42

The next generation Siemens MS ECUs introduced many of the OBD2 features. This includes Catalytic Converter monitoring and Long / Short term Fueling and Ignition Adaptation. The MS41 was used on the M52 series of engines, MS42 on the M52TU series, and MS43 on the M43 4 Cylinders.

The OBD2 P codes fault protocol was not activated in European markets on this group, as currently it was not required by law.

Lambda Regulation Bank 1 Post Cat

Fault Code Table : MS43

The next generation Siemens MS ECUs introduced many of the OBD2 features. This includes Catalytic Converter monitoring and Long / Short term Fueling and Ignition Adaptation. The MS41 was used on the M52 series of engines, MS42 on the M52TU series, and MS43 on the M43 4 Cylinders.

The OBD2 P codes fault protocol was not activated in European markets on this group, as currently it was not required by law.

Misfire Cyl 7 with Cyl Cutout

Fault Code Table : DME MSS52

The MSS52 is an M Power ECU designed to run the E39 M5, the Z8 Roadster, and also the Wiesmann Roadsters. The MSS54 is used on the E46 M3 and on some Z3Ms. The system uses an Electronic Throttle to accurately control Air intake instead of the more common Cable throttles used on earlier vehicles

Misfire Cyl 7 with Cyl Cutout

Fault Code Table : DME MSS54

The MSS52 is an M Power ECU designed to run the E39 M5, the Z8 Roadster, and also the Wiesmann Roadsters. The MSS54 is used on the E46 M3 and on some Z3Ms. The system uses an Electronic Throttle to accurately control Air intake instead of the more common Cable throttles used on earlier vehicles

DME Control unit

Fault Code Table : BMS46

The Bosch BMS46 is a Hybrid ECU, created from a joint effort with Siemens, and is used in later M43 engines used in the Z3 and E46 series.

DME Control unit

Fault Code Table : BMS43

The Bosch BMS46 is a Hybrid ECU, created from a joint effort with Siemens, and is used in later M43 engines used in the Z3 and E46 series.

About | Contact | Privacy

Copyright © 2019 All rights reserved. BMW Faults are listed in here BMWFaultCodes.com .